FolkArt ® Texture Paint - White, 4 oz. - 2860

FolkArt® Texture Paint should not be applied to flexible surfaces because it may crack.

Yes, FolkArt® Texture Paint can be used on outdoor surfaces and projects if they are protected from the elements. If they will be exposed to the elements, they need to be sealed with FolkArt® Outdoor Varnish.

No you should not mix FolkArt® Texture Paint with extender or water. Mixing with any other liquid may increase cracking.

All FolkArt® Texture Paint colors can be intermixed to create custom colors. They can be mixed before use or mixed as they are applied to the project.

Yes, FolkArt® Texture Paint can be painted or antiqued after it has cured to change the color or finished look.

We recommend air drying the FolkArt® Texture Paint. Using a fan or hair dryer may remove the moisture from the paint too quickly and cause the paint to crack.

No, tinting FolkArt® Texture Paint with other paints may change the properties of the Texture Paint.

No, it is self sealing. If it will be exposed to the elements outdoors, it should be sealed with FolkArt® Outdoor Varnish.

FolkArt® Texture Paints dry in 24 hours. Total cure time is between 48 to 72 hours depending on the thickness of the paint and the humidity.

FolkArt® Texture Paint can be applied with a palette knife, a paint brush or a stencil brush. When using a paint brush or stencil brush, use a dabbing motion to get the most textured effect.

Clean brushes or applicators (brushes, palette knife) while wet with soap and water.

FolkArt® Texture Paint can be used on wood, terra cotta, paper mache, Styrofoam and most porous surfaces.

No, FolkArt® Texture Paint is not recommended for fabric application.

Decorated candles using Mod Podge ® or Royal Coat ® Decoupage Finish are meant for decorative purposes and not for illumination. Many of the decorations would catch fire and be hazardous if the candle were burned. However, if you are using a wide pillar candle and the decorations do not go to the top of the candle, it can be burned down slightly to create a well, then a votive candle inserted into the well. A new votive candle can be inserted when the old one is finished. Use extreme caution and good judgment when burning candles that have been decorated.

Yes, simply use stencil or painter’s tape to mask off a border. Load a Fabric Creations™ Sponge Cube with Soft Fabric Ink and pounce the color onto the masked area.

Be sure to allow the painted background area to dry thoroughly before stamping over it with a design.

Separate the strands of floss

Take one strand and double it (most cross stitches require 2 strands, while back stitches require just one.)

Thread the looped end of the strand through the eye of the needle

Pull the loop to the bottom

NEVER make knots in your floss, so as to ensure a smooth finished back.

Wet your brush and gently tap on a paper towel to remove excess water. Pick up paint by dipping one corner of the brush in one color.

Dip the opposite corner of the brush in another color. This will form triangles at each corner of the brush.

Stroke brush back and forth on a clean spot on your palette to blend the paint.

Flip brush over to the other side and push it away from you, blending on the same spot on the palette. Be sure to keep the colors in the same spot on the blending area of the palette.

Notice how a correctly loaded and blended brush should look. The paint fills the brush 3/4ths of the way up the brush, but does not get into the ferrule of the brush. When the brush is loaded correctly, your strokes should feel as though the bristles glide.

If the brush is coarse or splits, you do not have enough paint on the brush. Reload the brush as needed, but do not blend on the palette after each reload or your paint will start to become muddy in your brush, with the colors blending together.