Inbox Inspiration

Subscribe to the PLAID Crafts Newsletter,
and we’ll throw in $10 towards your next purchase.

Martha Stewart Crafts Holiday Greetings Adhesive Stencil Ornaments

Creating snow themed ornaments will warm the hearts of those who receive them as gifts and will twinkle with glitter on your own tree!

At a Glance:

#4766 Skill Level: Beginner Time:
  • Clock active
  • Clock active
  • Clock active
  • Clock active

This project features these great brands:

  • Martha Stewart Logo
  • Martha Stewart Glass Logo
supplies

Martha Stewart Crafts ® Dauber Set

Number Needed: 1 $0.00 $8.09
Item available exclusively at Walmart

Martha Stewart Crafts ® 2oz Gloss Opaque Glass Paint - Pesto

Number Needed: 1 $0.00 $3.59
Item available exclusively at Walmart

Martha Stewart Crafts ® 2oz Gloss Opaque Glass Paint - Chipotle

Number Needed: 1 $0.00 $3.59
Item available exclusively at Walmart

Martha Stewart Crafts ® 2oz Pearl Opaque Glass Paint - Mother of Pearl

Number Needed: 1 $0.00 $3.59
Item available exclusively at Walmart

Martha Stewart Crafts ® 2oz Metallic Opaque Glass Paint - Sterling

Number Needed: 1 $0.00 $3.59
Item available exclusively at Walmart

Martha Stewart Crafts ® 2oz Fine Glitter Translucent Glass Paint - Sterling

Number Needed: 1 $0.00 $4.09
Item available exclusively at Walmart
instructions

Other Supplies

Martha Stewart Crafts Glass Paint Holiday Greetings - Adhesive Stencils - Christmas, Glass ornaments, Brush basin or container for water, Paper towels, Rubbing alcohol, Foam plate

Instructions

1. Remove ornament hanger from glass disc. 

2. Pour small amount of rubbing alcohol inside ornament and swirl to remove dirt, dust, or grease film. Allow to dry thoroughly.

3. Pour approximately ½ tablespoon of paint into ornament and swirl until coated. Drain excess paint. Allow to dry; place ornament with opening on its side, on top of paper cup.  To speed drying time, place in front of fan.  Flip ornament approximately every 20 minutes to prevent pooling of paint.

4. When inside paint is dry, moisten paper towel with rubbing alcohol and wipe each ornament to remove any dirt, grease or soap film.  Allow to dry.

5. Peel adhesive stencil from backing sheet; set backing aside and save for future storage.

6. Position adhesive stencil on surface where desired; press in place.

Stenciling Instructions:
1. Squeeze a small amount of paint onto foam plate. 

2. Load the flat bottom edge of the foam pouncer or dauber with glass paint by dabbing into the puddle of paint.  Dab a few times more on a clean spot on the foam plate to ensure you have the entire foam pouncer loaded properly. 

3. Holding the foam pouncer as you would a pencil, begin dabbing straight up and down over the opening of the adhesive stencil.  Continue painting until the entire design area has been completed.

4. Set foam pouncer aside in container of water for cleaning.  While paint is still wet, neatly and carefully lift stencil by peeling away from the ornament surface.  NOTE:  Be careful not to drag stencil while removing it as your painted design may be blurred.

5.  Continue adding stenciled designs over surface until desired effect is achieved.  NOTE:  When repeating a stenciled design, it is best to clean the stencil between uses by rinsing in water and allowing the stencil to dry thoroughly.

6. To add depth to your ornament, apply a coat or two of desired paint color to back of ornament.  NOTE:  to add extra sparkle, apply two coats of fine glitter translucent paint prior to painting background color.  Allow each application of paint to thoroughly dry before applying the next.

7. If desired, add a stenciled design on the backside of the ornament as well.

8. Embellish snowflake designs with small dots of paint.  Use either a stylus dipped into a paint puddle then applied to the ornament or the writer tip of the paint bottle to apply painted dots.  If desired, when dry apply flat back pearls or gems.

9. Set completed project aside for 1 hour to thoroughly dry.

Curing Instructions:  Air Cure Technique – Air dry completed project for 21 days before using. 

PROJECT TIP: Set several ornaments up in an assembly line fashion to create all the fronts together then when dry, flip over to paint the backside of each ornament together.

Disclaimer: The information found in each project is presented in good faith, but no warranty is given, nor results guaranteed, nor is freedom from any patent to be inferred. Since we have no control over physical conditions surrounding the application of information herein contained, Plaid Enterprises, Inc. disclaims any liability for untoward results.

Important: Please be sure to thoroughly read the instructions for all products, paying particular attention to all cautions and warnings shown to ensure the proper and safe use of the product.

Copyright: All Rights Reserved. No part of this Project may be reproduced in any form without permission in writing, except for your personal use, except by reviewer, who may in reviewing this project, quote brief passages in a magazine or newspaper.