Inbox Inspiration

Subscribe to the PLAID Crafts Newsletter,
and we’ll throw in $10 towards your next purchase.

Halloween Charm Bracelet with Mod Podge

Making a Halloween charm bracelet is as easy as 1, 2, 3 when you use Mod Podge Podgeables and Halloween paper.

At a Glance:

Skill Level: Beginner Time:
  • Clock active
  • Clock active
  • Clock active
  • Clock active

This project features these great brands:

  • Mod Podge Finishes and Formulas Logo
  • Mod Podge Tools and Accessories  Logo
instructions

Other Supplies

Halloween Scrapbook Paper (small images), Pencil, Scissors, Gem Glue, Rhinestones, Silver Chain, Toggle Clasp, Jumprings, Pliers, Rhinestone Dangles

Instructions

When using jumprings, never pull them open. With a pair of pliers in each hand, hold one side the jumpring in one pliers and the other side in the other pliers. The split should be facing up. Move the pliers in a circle motion away and toward your chest to open the jumpring. Attach to your project and close by repeating the circle motion.

  1. Trace the Podgeable shapes over Halloween themed scrapbook paper. Cut out the designs. Do this for each shape.
  2. Apply a thin coat of Mod Podge to the top of the Podgeable square and to the back of the cut paper. Position the paper on the Podgeable. Smooth with your fingers to remove any air-bubbles. Apply a top-coat of Mod Podge to the photo. Dry for 2 hours. Do this for each shape.
  3. Using gem glue, attach rhinestones to the Podgeable shape. Allow to dry completely before moving onto the next step.
  4. Place the Podgeable shapes on a hard flat surface. Cover the square Podgeable with Dimensional Magic. Begin around the outer edge, work around the rhinestones and fill until the entire shape is covered. Dry for 24 hours in an undisturbed and non-drafty place. TOP: if you get an air-bubble, pop with a sewing pin.
  5. Using pliers and jumprings, attach a toggle clasp to a bracelet length of chain. The most common sizes are 6.5”, 7” and 8”.
  6. Begin in the center of the chain, using a jumpring, attach a Podgeable charm to the center of the chain. Evenly space and attach the remaining 4 Podgeable charms. In between each charm, attach a rhinestone dangle with a jumpring.

Tip: When using jumprings, never pull them open. With a pair of pliers in each hand, hold one side the jumpring in one pliers and the other side in the other pliers. The split should be facing up. Move the pliers in a circle motion away and toward your chest to open the jumpring. Attach to your project and close by repeating the circle motion.

supplies

Mod Podge ® Podgeable Clear Shapes

Number Needed: 1 $0.00 $3.29
Item available exclusively at Walmart

Mod Podge ® Gloss, 8 oz.

Number Needed: 1 $0.00 $7.29
Item available exclusively at Walmart

Mod Podge ® Dimensional Magic, 2 oz.

Number Needed: 1 $0.00 $6.29
Item available exclusively at Walmart

Disclaimer: The information found in each project is presented in good faith, but no warranty is given, nor results guaranteed, nor is freedom from any patent to be inferred. Since we have no control over physical conditions surrounding the application of information herein contained, Plaid Enterprises, Inc. disclaims any liability for untoward results.

Important: Please be sure to thoroughly read the instructions for all products, paying particular attention to all cautions and warnings shown to ensure the proper and safe use of the product.

Copyright: All Rights Reserved. No part of this Project may be reproduced in any form without permission in writing, except for your personal use, except by reviewer, who may in reviewing this project, quote brief passages in a magazine or newspaper.